Qualified Installer Quiz Ryan Reed2019-01-30T21:30:14-06:00 Step 1 of 250%Please read carefully...This test is designed to be a teaching tool to help you learn about the skyBeacon.You only have 1 chance to make a selection and you cannot change your answer without refreshing the page and starting over.When you make your answer selection, you will receive immediate feedback if the answer is correct or not. You may take this test as many times as required for you to receive a passing grade of 85% or higher, at which point the form will allow you to submit your test scores and contact information.Anything less than 85% will not allow you to submit your results.The quiz is open book so feel free to refer to the manuals during the quiz.Which frequency does skyBeacon transmit on?*978 MHz1200 MHz987 MHz1090 MHzWhich aircraft are suitable for skyBeacon installations?*Gliders without a transponderAircraft operating internationallyAircraft operating below FL180 (18,000’)What does adjusting the Transponder Monitor Threshold accomplish?*Improves GPS sensitivityChanges air/ground state thresholdConfigures sensitivity of transponder monitor to ensure Mode A/C replies are properly decodedWhat does adjusting Vs0 (stall speed) accomplish?*Alters position light brightnessConfigures maximum aircraft speedChanges air/ground state thresholdWhat devices can be used to set up skyBeacon? Select all that apply.* Android (phones or tablets) Windows computer iOS (iPhone or iPads) Mac computerWhat will happen in the navigation lights are switched off?*skyBeacon ADS-B OUT will continue to operate, but the navigation light will be extinguishedskyBeacon will operate as normalskyBeacon will stop working; you will lose all ADS-B OUT functionality and the navigation light will be extinguishedTrue or False: You can change settings of skyBeacon while the aircraft is in flight.*TrueFalseWhat do you need to adjust if the customer’s flight returns a failure of Mode 3/A code?*Emitter TypeTransponder Monitor ThresholdADS-B IN CapabilityICAO CodeTrue or False: You can install skyBeacon on aircraft that have rear position lights integrated into the wingtip position lights?*TrueFalseThe aircraft you are installing skyBeacon on has existing strobe lights connected to a high voltage anti-collision power supply. What is the correct installation practice in this case?*Connect the skyBeacon yellow strobe wire directly to the high voltage power supplyBypass the high voltage power supply and attach the yellow wire directly to the aircraft’s switched strobe powerSplice the black and yellow wires together and attach directly to the aircraft’s high voltage power supplyWhat do you do with the yellow wire if the aircraft does not have strobe lights? Select all that apply.* Cap and stow the yellow wire if strobe is not to be used Connect to the black ground wire Run a new wire to switched aircraft power (14/28V) and connect to the yellow wire if the strobe is to be used Cut the yellow wire as close to skyBeacon as possibleHow can you install skyBeacon on an aircraft not listed on the AML?*FAA Form 337 (FAA signature required)FAA Form 337 (no FAA signature required)Field Approval for major modificationHow long should you wait for an initial GPS fix after powering on?*Around 5 minutesAround 20 minutesAround 5 secondsAround 1 minuteWhen configured and operating normally, how do you know that skyBeacon has a GPS lock?*The skyBeacon LED annunciator on the pilot facing side of the fin flashes redThe skyBeacon LED annunciator on the pilot facing side of the fin remains on solidThe skyBeacon LED annunciator on the pilot facing side of the fin is extinguishedThe skyBeacon LED annunciator on the pilot facing side of the fin flashes greenWhere can the Wi-Fi password be found?*On the back of the skyBeacon unitOn a card that comes with skyBeaconIn the user manualI must call uAvionix to obtain itWingtip adapters are required for installations on?*Certain Piper aircraftAll aircraft installationsCertain Cessna aircraftAll aircraft with tip-tanksTrue or False: skyBeacon has ADS-B IN capability?*TrueFalseTrue or False: A placard staying “NAVIGATION LIGHTS MUST REMAIN ON FOR ADS-B OUT” must be installed.*TrueFalse
