tailBeacon works with any existing Mode C Transponder. uAvionix’s patented power transcoder technology seamlessly communicates with your existing legacy transponder over your aircraft’s electrical system.
Just because you are ADS-B equipped, doesn’t mean you want to be tracked. With tailBeacon’s Anonymous Mode, your aircraft identification remains hidden from the ADS-B OUT signal while squawking 1200. Anonymous Mode keeps the skies safe while protecting your privacy.
Self-Contained WAAS GPS
tailBeacon contains its own TSO Certified uAvionix truFYX WAAS GPS. You have no additional GPS to purchase or integrate with!
Watch Your Six
There’s more to tailBeacon than just ADS-B compliance. By replacing your existing rear position light with tailBeacon, you’re getting a 2x brighter LED nav light with a fraction of the power consumption. With tailBeacon’s 20,000 hour rated LEDs, you can fly with confidence knowing your rear’s covered.
Mounts with a Turn
The new tailBeacon is the easiest, most affordable installation on the market. Simply remove your existing position light, install the mounting bracket, connect to existing power wires, slide in tailBeacon, and turn to lock in place. It’s that easy!
Instant Setup and Configuration
Mechanically installing tailBeacon is the first easy step. With uAvionix’s mobile app, configuration is just as simple. Our mobile application (available for both Apple iOS and Android) guides your installer through setting the necessary values including the ICAO address, emitter type, aircraft length, width and GPS offsets.
If you cannot get the phone or tablet to connect to the wifi OR it says “Incorrect password” OR it is stuck on the opening page,
Please try these steps:
Turn off the power to the Beacon
Close ALL apps on your device (On Apple devices that involves swiping the app away and Androids require a Force close)
Turn on Airplane mode (This will turn off Wifi on most devices so you will need to turn it back on. The main reason for doing this is to stop cellular data from being transmitted and interfering with the lower power Wifi signal. If you have a newer Samsung phone, we have seen instances where the Bluetooth also needs to be turned off. )
Power on the Beacon product (You now have 5 minutes to connect to the Beacon before the wifi shuts off. Once connected it will stay active until you get airborne)
Open the wifi page of the smart device (Located under Settings for Apple devices and Connections for Android users)
When you see the Beacon-XXXX wifi SSID pop up, tap it and enter the passphrase EXACTLY as printed on the supplied card or sticker.
Wait until it shows connected (You will get a note about No internet connection. This is normal)
Now open the skyBeacon app, it will open to the Monitor page. Enter your aircraft information
If this is still not working, you may need to have the aircraft outside
Can the tailBeacon be used on rotorcraft?Zane Woodson2020-03-27T12:00:10-05:00
uAvionix does not recommend installation on Bell 206B/L and OH-58 A, B and C models at this time. If you have installed a tailBeacon on the Bell 206B, 206L, or OH-58 models please contact our support team.
The following aircraft have been reported to have fitment issues by customers.Zane Woodson2020-04-27T08:53:18-05:00
In some cases with certain devices, the mobile data feature must be disabled to configure the skyBeacon. Some devices like the Motorola Moto lineup frequently display this behavior. We are tracking this issue and working on a resolution. To option to disable Mobile Data is found under Setting on most devices. Refer to your mobile device documentation for more information.
Do I need the internet to configure the skyBeacon or tailBeacon?Derrick Mitchell2019-09-04T15:58:31-05:00
No, you do not need the internet or an internet connection while configuring the skyBeacon. The “Wi-Fi” connection is simply a radio signal that connects the skyBeacon application on your mobile device to the skyBeacon. You will see a warning of “no internet connection,” but that doesn’t matter because you are not trying to connect to the internet; you are using the Wi-Fi radio signal as a connection for the mobile app to communicate with the skyBeacon.
How does tailBeacon install?Ryan Reed2019-09-06T13:18:28-05:00
tailBeacon is designed to be a direct replacement for the common navigation light or nav/strobe found on the tail of many aircraft. tailBeacon has the form factor and installation characteristics of a traditional Grimes style rear postion light, referred to as a Grimes model S or A-2064.
It is recommended that you download the tailBeacon installation and user instructions and carefully check the installation template with the aircraft prior to purchase ensuring that the tailBeacon will fit your aircraft.
A typical tailBeacon installation will take an installer around 15 minutes. This is the time taken for the physical installation of the tailBeacon to the aircraft and configure the device. Please note that all aircraft are different and can potentially affect the installation time. We strongly recommend verification that the tailBeacon will fit the aircraft prior to installation or modification.
Which transponders does the tailBeacon work with?Ryan Reed2020-08-23T16:31:20-05:00
The STC is for the Cessna 172. The tail installation satisfies FAA requirements and will enable subsequent tailBeacon installations to be performed on any “suitable aircraft” without STC as a minor alteration.
A suitable aircraft supports the installation of the tailBeacon without airframe modification.
The tailBeacon installation is considered a minor alteration and can be approved by the installer for most aircraft. At this time a form 337 should be completed and submitted along with the proper logbook entries. Please note, the installer must determine if the conditions are appropriate for installation on a specific aircraft. Additional guidance for ADS-B installation, performance verification, logbook entries and 337 instructions have been provided in the FAA policy memo titled “Installation Approval for ADS-B OUT Systems”
Does installation of tailBeacon require rudder balancing?Ryan Reed2019-09-04T16:01:55-05:00
tailBeacon weighs 80grams/2.9oz/0.176lbs including 6″ of 22AWG. The rebalancing of the rudder will depend on the weight difference between the existing light and the tailBeacon. In many cases, the weight difference is less than 0.5oz
How is the installation tested to ensure it meets the FAA Requirements?Ryan Reed2019-09-04T16:02:26-05:00
Once the tailBeacon has been installed it is required that the equipment be tested to show it meets the FAA requirements for ADS-B OUT. An Operational Flight Evaluation (often referred to as a performance flight) must be performed and verified by the FAA. Additionally, the installer may verify performance on the ground using an ADS-B ramp test set.
Ramp Test Equipment (ref. section 91.407(c)). Use ramp test equipment (e.g. Aeroflex IFR6000) to verify proper system configuration and compliance with section 91.227 equipment performance requirements.
Operational Flight Evaluation: See next FAQ titled: What does the Operational Flight Evaluation Consist Of?
What does the Operational Flight Evaluation consist of?Ryan Reed2019-09-04T16:03:06-05:00
To summarize the requirements of AC20-165B (see links below): The performance flight should take place for a minimum of 30 minutes from wheels up. The aircraft should climb to 3,000’+ AGL and perform a minimum of 2 360 degree turns in each direction. Banks in excess of 30 degrees and extreme maneuvers and attitudes should be avoided. Any climb or descent should be a minimum of 1 minute in length. The area of flight should have excellent radar and ADS-B coverage. A map of the current ADS-B coverage at various altitudes AGL is located here: https://www.faa.gov/nextgen/programs/adsb/ICM/
Yes, tailBeacon will meet the 2020 ADS-B requirements when paired with an existing operational Mode C transponder. tailBeacon meets or exceeds all required performance and environmental standards for use in the national airspace. The certified tailBeacon will ship with 4 separate TSO certifications.
UAT Transmitter: TSO-C154c Class B1S
WAAS GPS: TSO-C145d Class Beta I
Altitude Encoder: TSO C88b
Position Light: TSO-C30 Type III
Will tailBeacon work outside the U.S.?Ryan Reed2019-12-02T09:13:01-06:00
A skyBeacon/tailBeacon can legally be used to enter and exit United States airspace. Pilots must also be familiar with and comply with the destination country’s ADS-B rules if applicable. At this time Canada, Mexico, and the Bahamas do not have any ADS-B requirements for light aircraft.
Who can install the skyBeacon or tailBeacon TSO units?Ryan Reed2019-09-23T14:08:42-05:00
For certified aircraft, the skyBeacon and tailBeacon TSO units must at the very least be installed by an Airframe and Powerplant mechanic (A&P) and the installation must be reviewed and approved (signed off) by an IA. Part 145 shops and facilities with avionics expertise will optimize timely installation and downtime in addition to reducing overall cost.
What needs to be documented?Ryan Reed2019-09-04T16:05:14-05:00
The ADS-B OUT alteration must be documented in the aircraft maintenance record per section 43.9(a) and include the statement, ·’The installed ADS-B OUT system was shown to meet the equipment performance requirements of 14 CFR section 91.227.”
Do the aircraft position/nav lights need to remain on during all operations?Ryan Reed2019-09-04T16:05:44-05:00
Yes, the position lights need to remain switched on during all operations. Removing power from the position lights also removes power from skyBeacon and/or tailBeacon. According to 91.225(f) “Each person operating an aircraft equipped with ADS-B Out must operate this equipment in the transmit mode at all times.”
Does the TCAS limitation apply to my aircraft?Ryan Reed2019-09-04T16:06:09-05:00
The only impacted aircraft are those with active (interrogating) TCAS systems. These systems provide aural resolution advisories, and will generally be marked as TSO-C119. TCAS systems are required for Part 135 operations on large turbine powered aircraft.
Aircraft equipped with TIS or ADS-B In systems for traffic awareness are NOT impacted. Also not impacted are TCAS-like systems such as the Skywatch 497. ADS-B receivers providing data to a G1000, ForeFlight or other moving maps provide an additional level of situational awareness but they are NOT TCAS systems. There is no limitation on installing skyBeacon alongside these systems.
How is my device protected from theft?Ryan Reed2019-09-04T16:06:20-05:00
The certified skyBeacon and tailBeacon feature a unique password secured configuration interface via Wi-Fi. A user must enter the password to change the device configuration including the aircraft ICAO and callsign. The password is unique to the device, and once configured, cannot be reconfigured for another aircraft without that password. The password is essentially an anti-theft key, and should be kept secure with aircraft record. There are no external markings or indications on the skyBeacon or tailBeacon to indicate the password.
uAvionix will be able to provide the password if lost provided proof of purchase can be validated.
My tailBeacon questions have not been answered, where do I go for support?Ryan Reed2019-09-06T13:21:15-05:00